The following warnings occurred:
Warning [2] Undefined variable $search_thread - Line: 60 - File: showthread.php(1617) : eval()'d code PHP 8.1.28 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/showthread.php(1617) : eval()'d code 60 errorHandler->error_callback
/showthread.php 1617 eval



Austinsevenfriends › Austin Seven Friends Forum › Forum chat... v
Storing engines

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Storing engines
Mick Hanna Offline
Member
***
Joined: Aug 2017 Posts: 123 Threads: 23
Reputation: 0
Location: Doncaster, gateway to northern civilisation
#1
05-06-2018, 04:19 PM
I have a spare engine that I've repaired and refurbished that will be stowed beneath the bench to keep it out of the way. It's unlikely to be used for a while (fingers crossed) and I am wondering if it should be filled with oil before it is hidden from sight. I intend turning it over by hand every now and then. Any advice?
Reply
NickB Offline
Member
***
Joined: Aug 2017 Posts: 106 Threads: 3
Reputation: 0
#2
05-06-2018, 04:54 PM
I've not seen it with car engines, but when outboard engines are 'winterised' they are often run until just before fuel runs out and "fogging" oil is then sprayed in via the carburettor to protect the airways, carb and cylinders from corrosion.

Comes in a spray can. See link https://www.goldeagle.com/tips-tools/fog...ging-oils/
Reply
Bob Culver Offline
dogged member, NZ
*****
Joined: Aug 2017 Posts: 2,748 Threads: 31
Reputation: 95
Location: Auckland, NZ
#3
06-06-2018, 11:04 AM
Rust begets rust and our engines have been run without additives. Blanking off all openings  so damp air cannot circulate through block assists. Dunno about filling or sluicing water jacket with oil but judging by the rust flakes wish i had done with some old parts.
If the engine has been run getting copiuos oil onto valve stems is desirable and again air flow into manifolds should be blocked off.
Reply
Chris KC Offline
GO 6285
*****
Joined: Aug 2017 Posts: 3,214 Threads: 100
Reputation: 26
Location: Darkest Bedfordshire
#4
06-06-2018, 11:41 AM
Agree with above. Atmospheric moisture is perhaps the biggest thing you can tackle so seal in plastic and consider including an adequate qty of silica gel which will soak up whatever moisture is inside. Don't put in a wooden crate unless thus wrapped first as wood stores and releases moisture. Other than that make sure all surfaces are oiled or greased - new oil, not used. Oh yes and don't put your fingers all over newly machined surfaces, wipe them down with rag and WD40. My dad was building an engine in 1994 when he passed away, it's been stored lightly oiled in a DRY garage under lots of old blankets and still looking good.
Reply
Mick Hanna Offline
Member
***
Joined: Aug 2017 Posts: 123 Threads: 23
Reputation: 0
Location: Doncaster, gateway to northern civilisation
#5
06-06-2018, 01:33 PM
Some great advice. Thanks to all. I now wish I hadn't chucked all those little packets of silica gel away whenever something new arrived in the house!
Reply
Charles P Offline
Eternal Repairer
*****
Joined: Aug 2017 Posts: 1,437 Threads: 59
Reputation: 17
#6
06-06-2018, 02:09 PM
Try dessicant spark plugs
http://www.aircraftspruce.com/catalog/ep...rplugs.php
Reply
Chris KC Offline
GO 6285
*****
Joined: Aug 2017 Posts: 3,214 Threads: 100
Reputation: 26
Location: Darkest Bedfordshire
#7
06-06-2018, 02:17 PM
(06-06-2018, 02:09 PM)Charles P Wrote: Try dessicant spark plugs
http://www.aircraftspruce.com/catalog/ep...rplugs.php

Wow!
Reply
Viteran Offline
Member
***
Joined: Dec 2017 Posts: 100 Threads: 16
Reputation: 1
Location: South yorkshire
#8
06-06-2018, 03:07 PM
Impressive website, I like the whistle alert!
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)